October 31, 2022 11:33 am

osama

Ashley pellet stove error codes can be frustrating at times but don’t worry – we’re here to help. In this blog post, we’ll walk you through the most common error codes and troubleshooting tips for your Ashley pellet stove. So read on – you may find the answer to your question!

What Are The Different Ashley Pellet Stove Error Codes, And What Do They Mean?

If your Ashley pellet stove is experiencing an error, it will display an error code on the control panel. There are eight different error codes that you may see, and each one indicates a different problem. Here is what the different Ashley pellet stove error codes mean:

E1: The High-Limit Temperature Sensor Has Tripped

If the high-limit temperature sensor trips on your Ashley pellet stove, it could be due to inadequate ventilation, room fan failure, exhaust blockage, or an electrical opening in the over-temperature wiring or switch. To troubleshoot, first, check the vents and make sure they’re clear. Then check the fan to see if it’s working properly. If the fan is fine, try removing any blockages in the exhaust. Finally, check the over-temperature switch and wiring for any electrical opens. If you can’t find the source of the problem, call a qualified technician for assistance.

E2: Stove Ran Out Of Fuel During Normal Operation

Here are four possible causes of your pellet stove, and how you can investigate each one. First, check to see if the hopper is empty. If it is, then you’ll need to replenish your fuel supply. Second, see if the auger is jammed or not working properly. If it is, then you’ll need to clear the jam and/or replace the auger. Third, check the quality of your fuel. If the fire is burning too slowly or going out, then it’s possible that the fuel isn’t good enough quality. Lastly, check for an electrical opening in the low-temperature wiring or switch. If there is one, then you’ll need to repair or replace the switch or wiring. By troubleshooting each of these potential problems, you should be able to identify and fix the issue with your stove.

E3: The Stove Was Unable To Reach The Room Fan On Temperature Within The Startup Time

The potential causes for this error include flame or fuel quality causing the fire to burn too slowly or go out. The auger output may have experienced a failure or the jam hopper might have been empty on startup may also be a potential cause of this error. You may also use the internet as an investigative tool to help research and understand why this happened and how it could have been prevented.

his code indicates an overheating condition. The most likely cause is that the room where the stove is located is too small or that there is something blocking airflow to the stove. Make sure that the room where the stove is located is well-ventilated and clear any obstructions to airflow to resolve this issue.

E4: The Power Failed While The Stove Was Hot, And When It Was Restored, The Fire Was Out

Electrical Open in the low-temperature wiring or switch can cause this error to occur. Also, power loss can be a potential reason too.

E5: Blown Auger Output Fuse

If the auger output fuse in your Ashley pellet stove has blown, it is likely due to a problem with the auger motor. The auger motor may be jammed or defective, causing it to draw too much power and blow the fuse. If this is the case, you will need to replace the auger motor. You may also need to clean the auger housing and check the wiring for any loose connections. If the problem persists, you may need to consult a qualified technician for further diagnosis and repair.

E6: Blown Out Ignitor Output Fuse

This is caused by either the Ignitor shorting out or being bad. If the Ignitor is shorted out, it will need to be replaced. If the Ignitor is bad, it will need to be repaired. There are a few things that can cause the Ignitor to go bad, such as age, the wrong type of electrical current, or voltage that is too low. If the Ignitor is not working, the pilot light will not be able to stay lit. This can be dangerous because then the gas will not be burned off and could build up and explode.

E7: Blown Out Draft Fan (Exhaust Fan) Output Fuse

The draft fan, or exhaust fan, in your Ashley pellet stove helps to regulate the airflow and keep the fire burning evenly. If the motor becomes jammed or starts to fail, it can cause the fuse to blow. As a result, it’s important to keep an eye on the condition of your draft fan and replace it if necessary. Fortunately, this is a relatively easy task that can be completed in a matter of minutes. Simply remove the old motor and install the new one in its place. Be sure to follow the manufacturer’s instructions carefully to ensure optimal performance. By taking these simple steps, you can help keep your pellet stove in top condition and prevent costly repairs down the road.

E8: Blown Out Room Fan Output Fuse

There are a few potential causes for a room fan’s output fuse to blow. The most common cause is that the motor is jammed or bad. If the motor is jammed, it will draw too much power and cause the fuse to blow. If the motor is bad, it may also draw too much power and cause the fuse to blow. Other potential causes include loose wiring or a faulty switch. If the wiring is loose, it can create a short circuit that blows the fuse. If the switch is faulty, it may allow too much current to flow, again causing the fuse to blow. Whatever the cause, it’s important to replace the blown fuse as soon as possible to avoid damaging the room fan.

Conclusion

So, if you are experiencing any of the above issues with your Ashley pellet stove, be sure to refer to the information provided above for the corresponding error code and troubleshooting tips. Hopefully, this will help get your stove up and running again in no time! Have you had to deal with an error code on your Ashley pellet stove? If so, what was the solution? Let us know in the comments section below.

{"email":"Email address invalid","url":"Website address invalid","required":"Required field missing"}
>